ASTM F594 Nuts are made up of different alloys. These alloys are grouped into group 1 and group 2. The group 1 alloys have type 304 material and the group 2 alloys have type 316 material. There are different shapes and types of nuts in this specification. The ASTM F594 Hex Nuts are one of the preferred nuts for high torque applications because they can withstand high forces while installing and uninstalling.
ASTM F594 Nuts
ASTM F594 Hex Nuts
ASTM F594 Washers
The ASTM F594 Washers are used with these nuts to enable better tightening of the nuts. The material includes different amounts of carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, copper and molybdenum varying with the grades of the alloy. There are different diameters ranging from ¼ inches to 1 ½ inches and different strength values. The F594 Stainless Steel Washers are used to support the nuts and they are made in the same grade as the nuts. The minimum proof strength of the nuts is 70ksi for lower alloys and ranges up to 100ksi for higher alloys. The ASTM F594 Stainless Steel Nuts have high hardness values as well. The minimum Rockwell hardness ranges from B65 to C32 for various grades. There are different types such as the F594 Lug Nuts, wing nuts, hex nuts, square nuts and dome nuts. Each one is used in a different application such as automobile, engine parts, equipment, tools, construction and in other general corrosive applications.
Standards | Designation |
---|---|
ASTM | F594 |
Astm F594 Nuts Delivery time | custom product will according to special requirement, Regular product is about 7-15 days |
ASTM F594 Nuts Coatings | Cadmium, Black Oxide, Teflon, Galvanized, Zinc, Xylan, Others Upon Request |
Astm F594 Nuts Dimensions | ASME B18.3, B18.2.1 |
Melt Origin | South America/East Europe/Japan/Korea |
Product Origin | Made in India |
Astm F594 Nuts Certification | Dual Certified As per ASME & ASTM Codes |
Additional Certifications | Merkblatt AD 2000 W2 Certified,PED 97/23/EC Certified |
Mandatory Requirements | Free from Radioactive & Mercury Contamination |
Additional Requirements | NACE MR0175 / MR0103 /ISO 15156 Compliance |
Astm F594 Nuts Samples | Yes |
Nut Size (mm) |
Diameter* (mm) |
Height (mm) |
||
---|---|---|---|---|
Hex Nut |
Jam Nut |
Nylock Nut |
||
2 |
4 |
1.6 |
1.2 |
- |
2.5 |
5 |
2 |
1.6 |
- |
3 |
5.5 |
2.4 |
1.8 |
4 |
4 |
7 |
3.2 |
2.2 |
5 |
5 |
8 |
4 |
2.7 |
5 |
6 |
10 |
5 |
3.2 |
6 |
7 |
11 |
5.5 |
3.5 |
- |
8 |
13 |
6.5 |
4 |
8 |
10 |
17 |
8 |
5 |
10 |
12 |
19 |
10 |
6 |
12 |
14 |
22 |
11 |
7 |
14 |
16 |
24 |
13 |
8 |
16 |
18 |
27 |
15 |
9 |
18.5 |
20 |
30 |
16 |
10 |
20 |
* This is the diameter across the flats. It is also the size of wrench to use. |
Nominal Size or Basic Major Thread Diameter | F | G | H | ||||||
Width Across Flats |
Width Across Corners |
Thickness | |||||||
Basic | Max | Min | Max | Min | Basic | Max | Min | ||
1/4 | .2500 | 7/16 | .438 | .428 | .505 | .488 | 7/32 | .226 | .212 |
5/16 | .3125 | 1/2 | .500 | .489 | .577 | .557 | 17/64 | .273 | .258 |
3/8 | .3750 | 9/16 | .562 | .551 | .650 | .628 | 21/64 | .337 | .479 |
7/16 | .4375 | 11/16 | .688 | .675 | .794 | .768 | 3/8 | .385 | .365 |
1/2 | .5000 | 3/4 | .750 | .736 | .866 | .840 | 7/16 | .448 | .427 |
9/16 | .5625 | 7/8 | .875 | .861 | 1.010 | .982 | 31/64 | .496 | .473 |
5/8 | .6250 | 15/16 | .938 | .922 | 1.083 | 1.051 | 35/64 | .559 | .535 |
3/4 | .7500 | 1-1/8 | 1.125 | 1.088 | 1.299 | 1.240 | 41/64 | .665 | .617 |
7/8 | .8750 | 1-5/16 | 1.312 | 1.269 | 1.516 | 1.447 | 3/4 | .776 | .724 |
1 | 1.0000 | 1-1/2 | 1.500 | 1.450 | 1.732 | 1.653 | 55/64 | .887 | .831 |
1-1/8 | 1.1250 | 1-11/16 | 1.688 | 1.631 | 1.949 | 1.859 | 31/32 | .999 | .939 |
1-3/8 | 1.3750 | 2-1/16 | 2.062 | 1.994 | 2.382 | 2.273 | 1-11/64 | 1.206 | 1.138 |
1-1/2 | 1.500 | 2-1/4 | 2.250 | 2.175 | 2.598 | 2.480 | 1-9/32 | 1.ASTM A194 GR. 8 | 1.245 |
1-5/8 | 1.6250 | 2-7/16 | 2.438 | 2.356 | 2.815 | 2.686 | 1-25/64 | 1.429 | 1.353 |
1-3/4 | 1.7500 | 2-5/8 | 2.625 | 2.538 | 3.031 | 2.893 | 1-1/2 | 1.540 | 1.460 |
2 | 2.0000 | 3 | 3.000 | 2.900 | 3.464 | 3.306 | 1-23/32 | 1.763 | 1.675 |
2-1/4 | 2.2500 | 3-3/8 | 3.375 | 3.263 | 3.897 | 3.719 | 1-15/16 | 1.986 | 1.890 |
2-1/2 | 2.5000 | 3-3/4 | 3.750 | 3.625 | 4.330 | 4.133 | 2-5/32 | 2.209 | 2.105 |
2-3/4 | 2.7500 | 4-1/8 | 4.125 | 3.988 | 4.763 | 4.546 | 2-3/8 | 2.431 | 2.319 |
Nominal Size or Basic Major Thread Diameter | F | G | H | ||||||
Width Across Flats | Width Across Corners | Thickness | |||||||
Basic | Max | Min | Max | Min | Basic | Max | Min | ||
1/4 | .2500 | 1/2 | .500 | .488 | .577 | .556 | 15/64 | .250 | .218 |
5/16 | .3125 | 9/16 | .562 | .546 | .650 | .622 | 19/64 | .314 | .280 |
3/8 | .3750 | 11/16 | .688 | .669 | .794 | .763 | 23/64 | .377 | .341 |
7/16 | .4375 | 3/4 | .750 | .728 | .866 | .830 | 27/64 | .441 | .403 |
1/2 | .5000 | 7/8 | .875 | .850 | 1.010 | .969 | 31/64 | .504 | .464 |
9/16 | .5625 | 15/16 | .938 | .909 | 1.083 | 1.037 | 35/64 | .568 | .526 |
5/8 | .6250 | 1-1/16 | 1.062 | 1.031 | 1.227 | 1.175 | 39/64 | .631 | .587 |
3/4 | .7500 | 1-1/4 | 1.250 | 1.212 | 1.443 | 1.382 | 47/64 | .758 | .710 |
7/8 | .8750 | 1-7/16 | 1.438 | 1.394 | 1.660 | 1.589 | 55/64 | .885 | .833 |
1 | 1.0000 | 1-5/8 | 1.325 | 1.575 | 1.876 | 1.796 | 63/64 | 1.012 | .956 |
1-1/8 | 1.1250 | 1-13/16 | 1.812 | 1.756 | 2.093 | 2.002 | 1-7/64 | 1.139 | 1.079 |
1-1/4 | 1.2500 | 2 | 2.000 | 1.938 | 2.309 | 2.209 | 1-7/32 | 1.251 | 1.187 |
1-3/8 | 1.3750 | 2-3/16 | 2.188 | 2.119 | 2.526 | 2.416 | 1-11/32 | 1.378 | 1.460 |
1-1/2 | 1.5000 | 2-3/8 | 2.375 | 2.300 | 2.742 | 2.622 | 1-15/32 | 1.505 | 1.433 |
1-5/8 | 1.6250 | 2-9/16 | 2.562 | 2.481 | 2.959 | 2.828 | 1-19/32 | 1.632 | 1.556 |
1-3/4 | 1.7500 | 2-3/4 | 2.750 | 2.662 | 3.175 | 3.035 | 1-23/32 | 1.759 | 1.679 |
2 | 2.0000 | 3-1/8 | 3.125 | 3.025 | 3.608 | 3.449 | 1-31/32 | 2.013 | 1.925 |
2-1/4 | 2.2500 | 3-1/2 | 3.500 | 3.388 | 4.041 | 3.862 | 2-13/64 | 2.251 | 2.155 |
2-1/2 | 2.5000 | 3-7/8 | 3.875 | 3.750 | 4.474 | 4.275 | 2-29/64 | 2.505 | 2.401 |
2-3/4 | 2.7500 | 4-1/4 | 4.250 | 4.112 | 4.907 | 4.688 | 2-45/64 | 2.759 | 2.647 |
3 | 3.0000 | 4-5/8 | 4.625 | 4.475 | 5.340 | 5.102 | 2-61/64 | 3.013 | 2.893 |
3-1/4 | 3.2500 | 5 | 5.000 | 4.838 | 5.774 | 5.515 | 3-3/16 | 3.252 | 3.124 |
3-1/2 | 3.5000 | 5-3/8 | 5.375 | 5.200 | 6.207 | 5.928 | 3-7/16 | 3.506 | 3.370 |
3-3/4 | 3.7500 | 5-3/4 | 5.750 | 5.562 | 6.640 | 6.341 | 3-11/16 | 3.670 | 3.616 |
4 | 4.0000 | 6-1/8 | 6.125 | 5.925 | 7.073 | 6.755 | 3-15/16 | 4.014 | 3.862 |
Composition, %, maximum except as shown | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
UNS Designation | Alloy Group | Alloy | Carbon | Manganese | Phosphorus | Sulfur | Silicon | Chromium | Nickel | Copper | Molybdenum | Others |
Austenitic Alloys | ||||||||||||
S30200 | 1 | 303 | 0.15 | 2.00 | 0.200 | 0.150 min | 1 | 17.0 – 19.0 | 8.0 – 10.0 | — | 0.60 maxA | — |
S30323 | 1 | 303 Se | 0.15 | 2.00 | 0.200 | 0.060 | 1 | 17.0 – 19.0 | 8.0 – 10.0 | — | — | Se 0.15 min |
A30400 | 1 | 304 | 0.08 | 2.00 | 0.045 | 0.030 | 1 | 18.0 – 20.0 | 8.0 – 10.5 | 1.00 | — | — |
S30403 | 1 | 304 L | 0.03 | 2.00 | 0.045 | 0.030 | 1 | 18.0 – 20.0 | 8.0 – 12.0 | 1.00 | — | — |
S30500 | 1 | 305 | 0.12 | 2.00 | 0.045 | 0.030 | 1 | 17.0 – 19.0 | 10.5 – 13.0 | 1.00 | — | — |
S38400 | 1 | 384 | 0.08 | 2.00 | 0.045 | 0.030 | 1 | 15.0 – 17.0 | 17.0 – 19.0 | — | 0.50 maxA | — |
S20300 | 1 | XM1 | 0.08 | 5.00 – 6.50 | 0.040 | 0.18 – 0.35 | 1 | 16.0 – 18.0 | 5.0 – 6.5 | 1.75 – 2.25 | — | — |
S30430 | 1 | 18-9LW | 0.10 | 2.00 | 0.045 | 0.030 | 1 | 17.0 – 19.0 | 8.0 – 10.0 | 3.0 – 4.0 | — | — |
S30433 | 1 | 302HQ | 0.03 | 2.00 | 0.045 | 0.030 | 1 | 17.0 – 19.0 | 8.0 – 10.0 | 3.0 – 4.0 | — | — |
S31600 | 2 | 316 | 0.08 | 2.00 | 0.045 | 0.030 | 1 | 16.0 – 18.0 | 10.0 – 14.0 | — | 2.0 – 3.0 | — |
S31603 | 2 | 316 L | 0.03 | 2.00 | 0.045 | 0.030 | 1 | 16.0 – 18.0 | 10.0 – 14.0 | — | 2.0 – 3.0 | — |
S32100 | 3 | 321 | 0.08 | 2.00 | 0.045 | 0.030 | 1 | 17.0 – 19.0 | 9.0 – 12.0 | — | — | Ti 5 x C min |
S34700 | 3 | 347 | 0.08 | 2.00 | 0.045 | 0.030 | 1 | 17.0 – 19.0 | 9.0 – 13.0 | — | — | Cb+Ta 10 x C min |
Ferritic Alloys | ||||||||||||
S43000 | 4 | 430 | 0.12 | 1.00 | 0.040 | 0.030 | 1 | 16.0 – 18.0 | — | — | — | — |
S43020 | 4 | 430F | 0.12 | 1.25 | 0.060 | 0.150 min | 1 | 16.0 – 18.0 | — | — | 0.60 maxA | — |
Martensitic Alloys | ||||||||||||
S41000 | 5 | 410 | 0.15 | 1.00 | 0.040 | 0.030 | 1 | 11.5 – 13.5 | — | — | — | — |
S41600 | 5 | 416 | 0.15 | 1.25 | 0.060 | 0.150 min | 1 | 12.0 – 14.0 | — | — | 0.60 maxA | — |
S41623 | 5 | 416 Se | 0.15 | 1.25 | 0.060 | 0.060 | 1 | 12.0 – 14.0 | — | — | Se 0.15 min | — |
S43100 | 6 | 431 | 0.20 | 1.00 | 0.040 | 0.030 | 1 | 15.0 – 17.0 | 1.25 – 2.50 | — | — | — |
Precipitation Hardening Alloy | ||||||||||||
S17400 | 7 | 630 | 0.07 | 1.00 | 0.040 | 0.030 | 1 | 15.0 – 17.5 | 3.0-5.0 | — | — | Cb+Ta 0.15 – 0.45 |
Stainless Steel Alloys | ConditionB | Alloy Mechanical Property Marking | Nominal Diameter, inch | Proof Load, ksi, min | Rockwell Hardness | ||||
---|---|---|---|---|---|---|---|---|---|
Austenitic Alloys | |||||||||
1 (303, 304, 304L, 305, 384, XM1, 18-9LW, 302HQ, 303Se) | AF | F593A | 1/4 to 1-1/2, | 70 | B85 max, | ||||
1 (303, 304, 304L, 305, 384, XM1, 18-9LW, 302HQ, 303Se) | A | F593B | 1/4 to 1-1/2, | 75 | B65 to 95, | ||||
1 (303, 304, 304L, 305, 384, XM1, 18-9LW, 302HQ, 303Se) | CW1 | F593C | 1/4 to 5/8, | 100 | B95 to C322, | ||||
1 (303, 304, 304L, 305, 384, XM1, 18-9LW, 302HQ, 303Se) | CW2 | F593D | 3/4 to 1-1/2, | 85 | B80 to C32, | ||||
1 (303, 304, 304L, 305, 384, XM1, 18-9LW, 302HQ, 303Se) | SH1 | F593A | 1/4 to 5/8, | 120 | C24 to C36, | ||||
1 (303, 304, 304L, 305, 384, XM1, 18-9LW, 302HQ, 303Se) | SH2 | F593B | 3/4 to 1, | 110 | C20 to C32, | ||||
1 (303, 304, 304L, 305, 384, XM1, 18-9LW, 302HQ, 303Se) | SH3 | F593C | 1-1/8 to 1-1/4, | 100 | B95 to C30, | ||||
1 (303, 304, 304L, 305, 384, XM1, 18-9LW, 302HQ, 303Se) | SH4 | F593D | 1-3/8 to 1-1/2, | 85 | B90 to C28, | ||||
2 (316, 316L) | AF | F593E | 1/4 to 1-1/2″, | 70 | B85 max, | ||||
2 (316, 316L) | A | F593F | 1/4 to 1-1/2″, | 75 | B65 to 95, | ||||
2 (316, 316L) | CW1 | F593G | 1/4 to 5/8, | 100 | B95 to C322, | ||||
2 (316, 316L) | CW2 | F593H | 3/4 to 1-1/2, | 85 | B80 to C32, | ||||
2 (316, 316L) | SH1 | F593E | 1/4 to 5/8, | 120 | C24 to C36, | ||||
2 (316, 316L) | SH2 | F593F | 3/4 to 1, | 110 | C20 to C32, | ||||
2 (316, 316L) | SH3 | F593G | 1-1/8 to 1-1/4, | 100 | B95 to C30, | ||||
2 (316, 316L) | SH4 | F593H | 1-3/8 to 1-1/2, | 85 | B90 to C28, | ||||
3 (321, 347) | AF | F593J | 1/4 to 1-1/2, | 70 | B85 max | ||||
3 (321, 347) | A | F593K | 1/4 to 1-1/2, | 75 | B65 to 95, | ||||
3 (321, 347) | CW1 | F593L | 1/4 to 5/8, | 100 | B95 to C322, | ||||
3 (321, 347) | CW2 | F593M | 3/4 to 1-1/2, | 85 | B80 to C32, | ||||
3 (321, 347) | SH1 | F593J | 1/4 to 5/8, | 120 | C24 to C36, | ||||
3 (321, 347) | SH2 | F593K | 3/4 to 1, | 110 | C20 to C32, | ||||
3 (321, 347) | SH3 | F593L | 1-1/8 to 1-1/4, | 100 | B95 to C30, | ||||
3 (321, 347) | SH4 | F593M | 1-3/8 to 1-1/2, | 85 | B90 to C28, | ||||
Ferritic Alloys | |||||||||
4 (430, 430F) | A | F593N | 1/4 to 1-1/2, | 55 | B85 max | ||||
4 (430, 430F) | CW1 | F593V | 1/4 to 5/8, | 60 | B75 to 98, | ||||
4 (430, 430F) | CW2 | F593W | 3/4 to 1-1/2, | 55 | B65 to 95, | ||||
Martensitic Alloys | |||||||||
5 (410, 416, 416Se) | H | F593P | 1/4 to 1-1/2, | 100 | C20 to 30, | ||||
5 (410, 416, 416Se) | HT | F593R | 1/4 to 1-1/2, | 160 | C34 to 45, | ||||
6 (431) | H | F593S | 1/4 to 1-1/2, | 125 | C25 to 32, | ||||
6 (431) | HT | F593T | 1/4 to 1-1/2, | 180 | C40 to 48, | ||||
Precipitation Hardening Alloy | |||||||||
7 (630) | AH | F593U | 1/4 to 1-1/2, | 135 | C28 to 38, |