En 14399-6 Washer
DIN EN 14399-6 Chamfered washer and M42 Flat Washer manufacturer in India
The washers are cold forged and the finishes are according to the ASTM A380 or A380M. The manufacturing process can also be cold heading, wire drawing, heat treatment, insert tapping, inspection, packing and surface plating. The En 14399 6 Washer M24 was also used to be known as the high strength structural bolting assemblies. These are used for preloading of the high strength structural assemblies. The hardness of this washer and the En 14399-6 equivalent types range from 300HV to 370HV. The application of the washers in preload assemblies provides better fatigue performance. The washers also enable the fasteners not to loosen under high vibrations. The DIN EN 14399 Part 6 Structural Flat Washers perform differently with different types of fasteners, the screw type of the fasteners, the material type and the size. The EN 14399-6 Plain chamfer washers work better with good fasteners; the performance decreases with corrosion and deformation of the fasteners, wearing off of the threads, etc. The DIN EN 14399-6 Thru-Hardened Steel Structural Flat Washer is used in high strength, high stress and high tensile applications such as engine part assemblies, construction assemblies and in higher industrial application assemblies. The sizes of the ISO EN 14399-6 Flat Washers range from #2 through #12 with inside diameters ranging from 3/32 inches to ¼ inches and from ¼ inches to 2inches with inside diameters ranging from 9/32 inches to 1 1/16 inches.
EN 14399-6 Washer
DIN 6916 Flat washer
EN 14399 6 Washer M24
Table of Content
Din En 14399-6 Chamfered washer is a type of washer that has a symmetrical slope on the edge of the washer. The size of the washer can range from M2 to M100. There are different dimensions to the washers based on the standards. The electroplating, hot dip galvanizing and rust preventing finishes are available for different types and sizes of washers such as the En 14399 6 Washer M42.
Find EN 14399 6 Washer M24 equivalents
| NOM SIZE | Inner Dia (d) Basic Tol (+) | Outer Dia (d1) Max | WIDTH (b) Basic Tol (+ or -) | THICKNESS (S) Basic Tol (+ or -) | Weight per 1000 in Kgs | |||
| 4 | 4.1 | 0.3 | 7.6 | 1.5 | 0.1 | 0.9 | 0.1 | 0.18 |
| 5 | 5.1 | 0.3 | 9.2 | 1.8 | 0.1 | 1.2 | 0.1 | 0.36 |
| 8 | 8.1 | 0.4 | 14.8 | 3 | 0.15 | 2 | 0.1 | 1.60 |
| 10 | 10.2 | 0.5 | 18.1 | 3.5 | 0.2 | 2.2 | 0.15 | 2.53 |
| 16 | 16.2 | 0.8 | 27.4 | 5 | 0.2 | 3.5 | 0.2 | 8.91 |
| 18 | 18.2 | 0.8 | 29.4 | 5 | 0.2 | 3.5 | 0.2 | 9.73 |
| 22 | 22.5 | 1 | 35.9 | 6 | 0.2 | 4 | 0.2 | 16.50 |
| 24 | 24.5 | 1 | 40 | 7 | 0.25 | 5 | 0.2 | 26.20 |
| 30 | 30.5 | 1.2 | 48.2 | 8 | 0.25 | 6 | 0.2 | 44.30 |
| 36 | 36.5 | 1.2 | 58.2 | 10 | 0.25 | 6 | 0.2 | 67.30 |
| 39 | 39.5 | 1.2 | 61.2 | 10 | 0.25 | 6 | 0.2 | 71.70 |
| 45 | 45.5 | 1.2 | 71.2 | 12 | 0.25 | 7 | 0.25 | 117.00 |
| 48 | 49 | 1.5 | 75 | 12 | 0.25 | 7 | 0.25 | 123.00 |
Get EN 14399-6 Plain chamfer washers Specifications, DIN EN 14399-6 Thru-Hardened Steel Structural Flat Washer rate chart
Bolt Size |
USS |
SAE |
||||
OD (in.) |
ID (in.) |
Thickness |
OD (in.) |
ID (in.) |
Thickness |
|
1/8 (#6) |
0.375 |
0.156 |
.036/.065 |
|||
5/32 (#8) |
0.438 |
0.188 |
.036/.065 |
|||
3/16 (#10) |
0.560 |
0.250 |
.036/.065 |
0.500 |
0.220 |
.036/.065 |
7/32 (#12) |
0.562 |
0.250 |
.051/.080 |
|||
1/4 (#14) |
0.734 |
0.312 |
.051/.080 |
0.625 |
0.281 |
.051/.080 |
5/16 |
0.875 |
0.375 |
.064/.104 |
0.688 |
0.344 |
.051/.080 |
3/8 |
1.000 |
0.438 |
.064/.104 |
0.812 |
0.406 |
.051/.080 |
7/16 |
1.250 |
0.500 |
.064/.104 |
0.922 |
0.469 |
.051/.080 |
1/2 |
1.375 |
0.562 |
.086/.132 |
1.062 |
0.531 |
.074/.121 |
9/16 |
1.469 |
0.625 |
.086/.132 |
1.156 |
0.594 |
.074/.121 |
5/8 |
1.750 |
0.688 |
.108/.160 |
1.312 |
0.656 |
.074/.121 |
3/4 |
2.000 |
0.812 |
.122/.177 |
1.469 |
0.812 |
.108/.160 |
7/8 |
2.250 |
0.938 |
.136/.192 |
1.750 |
0.938 |
.108/.160 |
1 |
2.500 |
1.062 |
.136/.192 |
2.000 |
1.062 |
.108/.160 |
1 1/8 |
2.750 |
1.250 |
.136/.192 |
2.250 |
1.250 |
.108/.160 |
1 1/4 |
3.000 |
1.375 |
.136/.192 |
2.500 |
1.375 |
.136/.192 |
1 3/8 |
3.250 |
1.500 |
.153/.213 |
2.750 |
1.500 |
.136/.213 |
1 1/2 |
3.500 |
1.625 |
.153/.213 |
3.000 |
1.625 |
.153/.213 |
1 5/8 |
3.750 |
1.750 |
.153/.213 |
|||
1 3/4 |
4.000 |
1.875 |
.153/.213 |
|||
1 7/8 |
4.250 |
2.000 |
.153/.213 |
|||
2 |
4.500 |
2.125 |
.153/.213 |
|||
2 1/4 |
4.750 |
2.375 |
.320/.248 |
|||
2 1/2 |
5.000 |
2.625 |
.210/.280 |
|||
2 3/4 |
5.250 |
2.875 |
.228/.410S |
|||
3 |
5.500 |
3.125 |
.249/.327 |
|||
Refer DIN EN 14399 Part 6 Structural Flat Washers, DIN 6916 Washer Weight chart, M20 Flat Washer Manufacturers in India
| Size | USS | SAE | ||||
|---|---|---|---|---|---|---|
| Inside Diameter (A) |
Outside Diameter (B) |
Thickness (C) |
Inside Diameter (A) |
Outside Diameter (B) |
Thickness (C) |
|
| #2 | - | - | - | 3/32" | 1/4" | 0.020" |
| #4 | - | - | - | 1/8" | 5/16" | 0.032" |
| #6 | - | - | - | 5/32" | 3/8" | 0.049" |
| #8 | - | - | - | 3/16" | 7/16" | 0.049" |
| #10 | - | - | - | 7/32" | 1/2" | 0.049" |
| #12 | - | - | - | 1/4" | 9/16" | 0.065" |
| 5/16" | 3/8" | 7/8" | 0.083" | 11/32" | 11/16" | 0.065" |
| 3/8" | 7/16" | 1" | 0.083" | 13/32" | 13/16" | 0.065" |
| 1/2" | 9/16" | 1-3/8" | 0.109" | 17/32" | 1-1/16" | 0.095" |
| 9/16" | 5/8" | 1-15/32" | 0.109" | 19/32" | 1-5/32" | 0.095" |
| 5/8" | 11/16" | 1-3/4" | 0.134" | 21/32" | 1-5/16" | 0.095" |
| 7/8" | 15/16" | 2-1/4" | 0.165" | 15/16" | 1-3/4" | 0.134" |
| 1" | 1-1/16" | 2-1/2" | 0.165" | 1-1/16" | 2" | 0.134" |
| 1-1/4" | 1-3/8" | 3" | 0.165" | - | - | - |
| 1-3/8" | 1-1/2" | 3-1/4" | 0.180" | - | - | - |
| 1-5/8" | 1-3/4" | 3-3/4" | 0.180" | - | - | - |
| 2" | 2-1/8" | 4-1/2" | 0.213" | - | - | - |
| Product name | EN 14399-6 Washer |
|---|---|
| Place of Origin | India |
| Standard | EN 14399-6 |
| DIN Standard | DIN 6916 |
|
Passivation /plain |
| Finishing | Zinc Plated (Yellow, White, Blue, Black), Hop Dip Galvanized (HDG) phosphorization, Black Oxide, Geomet, Dacroment, anodization, Nickel plated, Zinc-Nickel plated, Brass Plated, Tin Plated, Black Plated, Copper Plated, Gold Plated, Salt fog test |
| EN 14399-6 Washer Size | M2 – M100 |
| EN 14399-6 Washer Application | Wind tower, Nuclear power, Railway, Automotive industry, Construction, Electronic industry |
| Dimensions | ASME B18.6.3 *Exception: screws 6 inches and shorter are fully threaded. |
| Drive Style | Type I |
| EN 14399-6 Washer Material | 18-8 Stainless Steel, stainless steel ss 304/ SS316 A2/A4, SS201, SS303, SS304, SS316, SS316L, SS904L, A2-70; A4-70; A4-80 |
| Finish | Per ASTM A380/A380M |
| Production technology | Cold Forged |
| Manufacturing Process | Wire Drawing, Cold Heading, Insert tapping, Heat Treatment, Surface Plating, Inspection, Packing |
| Surface treatment of stainless steel Hex Bolt |
|
| MOQ | 10 pieces |
| Delivery time | Regular product is about 7-15 days, custom product will according to special requirement |
| Others | OEM, ODM, ±0.03MM tolerance |
| Coatings | Black Oxide, Cadmium, Galvanized, Teflon, Xylan, Zinc, Others Upon Request |
| Tolerance of stainless steel Hex Bolt | +/-0.01mm to +/-0.05mm |
| Samples | Yes |
| Payment Terms | T/T, Paypal, Western Union, L/C or Trade Assurance 30% deposit & balance before shipping |